- 1 What happens if you overtighten axle nut?
- 2 What happens if I Overtorque a bolt?
- 3 Can you over tighten an axle nut?
- 4 Can you over tighten a motorcycle axle?
- 5 How do I tighten my axle?
- 6 Can a loose axle nut symptoms?
- 7 How do you check if a bolt is over torqued?
- 8 Is it bad to over torque head bolts?
- 9 What happens if head bolts are not tight enough?
- 10 How tight should axle bolts be?
- 11 Do you have to replace axle nut?
What happens if you overtighten axle nut?
Re: What Happens If I overtighten the big axle Nut? You can break the nut, but it’s almost impossible. Most tighten as hard as they can get it on. I use a good 1/2″ impact and big compressor.
What happens if I Overtorque a bolt?
If the bolt is over-torqued, the tension can: Crush the installation material. Shorten the life of the bolt by putting too much force on it. Damage the threads by exceeding their load capacity.
Can you over tighten an axle nut?
An axle nut that is too tight will put too much preload on the hub bearings thus diminishing their life expectancy. Too loose is no bueno either. No they do not.
Can you over tighten a motorcycle axle?
If you over – tighten the rear axle you could strip the threads on the axle but more likely will put more pressure on the wheel bearing. Over – tightening the axle nut can also make the wheel “drag.” If it feels like the wheel is sliding, that sounds more like you ‘re missing a spacer to me!
How do I tighten my axle?
Tighten the axle nut with a socket and torque wrench; torque the axle nut between 15 to 20-ft pounds of torque to preload the axle bearings. Rotate the hub eight to 10 revolutions by hand to fully seat the bearing races. Loosen the axle nut until it is freely loose, then finger- tighten the axle nut.
Can a loose axle nut symptoms?
If the nut is loose the bearings will not be seated so you will get a “mixed” symptom. Torque the nut then go for a drive, the bearings if shot will most likely cause a vibration at a non prescribed speed depending on how shot the bearing is and the type of bearing on it.
How do you check if a bolt is over torqued?
If you set your torque wrench to the specified torque for the fastener you’re checking and the wrench clicks and there is no movement of the fastener, how do you know the fastener was not over – torqued? The only way to accurately check the torque of a suspected fastener is to loosen it and re- torque it.
Is it bad to over torque head bolts?
When you overtorque above 15% of recommended which in this case would be about 95 ft/lbs you basically turn the fastener into a rubber band. Some of the fasteners will stretch and you will have uneven torque. Add heat and pressure and head gasket blows and the head can even warp.
What happens if head bolts are not tight enough?
But even the best head gasket won’t maintain a tight seal if the head bolts have not been properly torqued. Uneven loading created by unevenly tightened head bolts can distort the head. Over a period of time, this may cause the head to take a permanent set.
How tight should axle bolts be?
Expert Reply: The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.
Do you have to replace axle nut?
How important to replace axle nut with a new one every time you remove it? Official Ford service procedure states that if you have to remove an axle nut, you should discard it and replace it with a brand-new one.